PSC SP400rf Uživatelský manuál stáhnout pdf (Strana 25)

R44-1027 19

INTERFACE

RS-232

SET -------------------------------------

DISABLE HARDWARE CONTROL --

ENABLE CTS/RTS FLOW CONTROL -

ENABLE CTS SCAN CONTROL --

ENABLE XON/ XOFF ------------

DISABLE XON/XOFF ------------

END -------------------------------------

XON/XOFF

HARDWARE

CONTROL

SOFTWARE CONTROL

XON/XOFF — this is software handshaking that allows the host to

control data transmission. If the host sends an XOFF command to

the scanner, the scanner will not send the barcode data until it

receives an XON command from the host. If the host sends the

XOFF command during data transmission, the host will receive no

more than two additional characters.

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 111 112

REQUENCY 1
PSC Scanning, Inc 2
Contents 3
Symbologies 4
Appendix A 5
Appendix B 5
Appendix C 5
INTRODUCTION 7
CHANGING INTERFACES 8
INFORMATION 9
PROGRAMMING OVERVIEW 10
THE PROGRAMMING SESSION 11
IF YOU MAKE A MISTAKE 12
RETURN TO FACTORY SETTINGS 12
CONFIGURATION UPLOAD 12
WHERE TO GO FROM HERE 13
ORT 5B INTERFACE SELECTION 14
ORT 9A, 9B, 9C, 9E SETTINGS 15
ORT E INTERFACE SELECTION 16
OCIA INTERFACE SELECTION 17
SNI OCIA INTERFACE SELECTION 17
OCIA OPTIONS 18
R44-1027 13 19
WAND EMULATION 19
INTERFACE 19
MULATION 20
NTERFACE 20
RS-232 INTERFACE SELECTION 21
AUD RATE 22
R44-1027 17 23
HARDWARE CONTROL 24
SOFTWARE CONTROL 25
MILLISECONDS 27
NTERCHARACTER 27
I/F Type PCs Supported 28
R44-1027 25 31
IMPORTANT 32
IBMXXXX STI WEDGE 32
PREFIX & SUFFIX 33
ABEL TRANSMIT 35
ORMAT CONFIG 35
ET SUFFIX 36
NE CHARACTER ONLY 38
ASCII CHARACTER SET 39
ONTINUED 41
R44-1027 37 43
R44-1027 39 45
SYMBOLOGIES 47
SYMBOLOGY OPTIONS OVERVIEW 48
SYMBOLOGY SELECTION 49
UPC/EAN OPTIONS 51
UPC/EAN EXPANSION 52
UPC/EAN ADD-ONS 53
END CHECK DIGIT 55
PRICE/WEIGHT CHECK DIGIT 56
CODE 39 OPTIONS 57
CODE 39 (CONTINUED) 58
ODE 39 MINIMUM 60
ABEL LENGTH 60
INTERLEAVED 2 OF 5 61
YMBOLOGY 62
ELECTION 62
ET FIXED 63
ETTING FIXED LENGTHS 63
ETTING MINIMUM LABEL LENGTH 63
R44-1027 59 65
STANDARD 2 OF 5 66
ORMAL STANDARD 2 OF 5 67
TANDARD 2 OF 5 67
ET FIRST FIXED LENGTH 69
CODABAR OPTIONS 71
Start/Stop 73
Standard Factory Settings 73
CODABAR FIXED LENGTH 74
R44-1027 69 75
MSI/PLESSEY CHECK DIGIT 76
NABLE MSI/PLESSEY FIXED 77
ISABLE MSI/PLESSEY FIXED 77
NABLE FIXED L 77
ET SECOND FIXED LENGTH 78
O SECOND FIXED LENGTH 78
LESSEY SET FIXED 78
NABLE 79
YMBOLOGY ID PREFIX 79
GENERAL FEATURES 80
COMMUNICATIONS PROTOCOL 81
FEATURES 83
ET STX 85
ET ETX 85
ET STX/ETX 85
"When to Beep" 86
CTS enabled 88
R44-1027 83 89
“WHEN TO BEEP” OPTIONS 90
R44-1027 87 93
BEEPER VOLUME 94
RADIO CHANNEL FREQUENCY 95
Radio Channel Frequency 96
AIT TIME FOR HOST ACKNOWLEDGE 97
IME FOR HOST 98
CKNOWLEDGE 98
READ VERIFICATION 99
Programming Guide 100
LOW BATTERY INDICATION METHOD 101
APPENDIX A 102
STANDARD FACTORY SETTINGS 102
TANDARD 2 OF 5 103
ISC. GENERAL FEATURES 104
EAD VERIFICATION 104
TEM ON/OFF FILE 104
UDIBLE INDICATOR SETTINGS 104
INTERFACE-DISCRETE DEFAULTS 105
IBM INTERFACES 106
APPENDIX B 107
ADDITIONAL INFORMATION 107
APPENDIX C 108
SAMPLE BARCODES 108
1 101234 567891 109
LANK PAGE 111
Corporate Headquarters 112

Komentáře k této Příručce

Žádné komentáře

PSC SP400rf Uživatelský manuál Strana 25

Komentáře k této Příručce

Související produkty a manuály pro Čtečky čárových kódů PSC SP400rf